Detalles del producto

The PerfectCharge MCA 1215 has two battery outputs, so it can simultaneously charge one battery plus the starter battery. And very gently too, using advanced 6-step charging technology. With its compact and lightweight design and practical screw connections, it can be installed quickly and hassle-free. Featuring an input voltage range of 110–230 V, it can be used anywhere in the world and will charge reliably even when the input voltage drops. Ideal for frequent travellers and globetrotters. Useful enhancements: remote control, battery sensor, temperature sensor or Dometic MPC 01 battery controller for up to 30 % faster charging.

Details:
  • Advanced 6-step charging technology.
  • Automatic shut-off after charging or after 8/16 hrs. (adjustable)
  • Input voltage: 90-260 V
  • Adjustable cut-off voltage: 14.4/14.8 V
  • Reverse polarity and short circuit protected
  • Mounting plate
  • Can also be used as a power supply

Technical Data
Battery types Lead acid, Gel, AGM
Heat dissipation Fan
Charging mode 6-step
Max. ambient temperature -20 °C to +50 °C
Storage temperature -40 °C to +85 °C
Humidity 20 - 90 %
Alarm signal Via relay contact
Communication Via LIN-BUS
Sleep mode With remote control (optional) or DIP-switch
Remote control (optional) On/Off switch, 3-colour LED, selectable sleep mode
Dimensions (LxWxH) 238 x 179 x 63 mm
Weight 1.6 kg
Certification CE
Protections
Output short-circuit Current reduced to 25% of its max
Overvoltage 16 V
Overheating of battery charger 100 °C +/- 5 °C (internally measured)
Overheating of battery 52 °C +/- 5 °C (with optional battery sensor)
Input
Nominal input voltage 90 - 260 V
Input frequency 50 - 60 Hz
Efficiency at 230 V ~ 87 %
Input current at 100 V ~ 2.5 A
Input current at 240 V ~ 1.07 A
Output
Charging voltage 14.4 V / 14.7 V
Trickle charging 13.8 V
Nominal charging current 15 A
Charging current 0 - 15 A
Outputs 1
ESB-output(for starter battery) 1
ESB-charging voltage 13.8 V
ESB-charging current 2 A


Tips:
To CN2 connector
  • A potential-free change-over switch with 3 contacts is available for the alarm function, e.g. For an audible alarm.
  • Pin 1 = NC (normally closed), is connected to pin 3 in the idle state, connection is opened in the event of an alarm.
  • Pin 2 = NO (normally open), is open in the idle state, is connected to pin 3 in the event of an alarm.
  • Pin 3 = COM (common), is the common contact of the changeover switch.
  • All contacts of the change-over switch are potential-free, so they have no reference to PLUS or MINUS.
  • Sleep mode can be controlled by an external (optional) ON / OFF switch, which is connected to pins 4 and 5. When the switch is on, the sleep mode is active.
  • Pin 4 = control input sleep mode
  • Pin 5 = MINUS
Optionally, a remote control for sleep mode or to display the current operating mode as well as a temperature sensor are available. The charging characteristic of the device refers to room temperature. The sensor is adjusted to a voltage of 20 mV /°C.

Documentos

multi-flag Manual
PDF, 2,93 MB
multi-flag Guía rápida
PDF, 392,09 KB
de-flag Guía rápida
PDF, 183,86 KB

Esto es lo que otros clientes de SVB opinan

Evaluaciones 100% auténticas
Hasta el momento no hay evaluaciones de este producto

Clientes preguntan a clientes

Haga sus preguntas a otros clientes de SVB que ya han comprado este producto y obtenga su opinión.

Su pregunta será automáticamente enviada a otros clientes de SVB y publicada en la página del producto. Por favor no realice preguntas que sólo el equipo de SVB puede responder, como el estado de un pedido o la disponibilidad de un producto. Para preguntas que se refieren a un pedido, por favor contacte a nuestro equipo SVB por email info@svb-marine.es o por teléfono al: 960 13 06 40 .

Aún no existen preguntas sobre este producto. ¡Sea el primero en realizar una pregunta!